This page cover the S355NL-Z35/S355NL-Z35 Chemical element, Mechanical Properties, S355NL-Z35 Datasheet, Cross Reference of S355NL-Z35 Mainly used for EN 10025-2 S355J2 high strength structural steel plate S355 a structural grade steel with a minimum yield strength of 355 N/mm² which widely used in the engineering and construction industries. S355 offers high yield and tensile strength and is supplied with a variety of treatments and test options to ensure it is a highly usable steel in your various projects.
Structural Steel EN10025. S355NL; S355J2+N; S355J2+N. S355J2+N is a low carbon steel grade primarily used in applcations where better mechanical properties are needed in comparison to S275.J2 signifies that the material has been impact tested at -20 o C, the plate is produced in a fully killed process and supplied in either a normalised or controlled rolled condidition. S355K2+N Steel PlateThe S355K2+ N plates have much superior impact properties to S355 J2 + N plates as the energy used in the Charpy V notch test is increased from 27J to 40J. The standard test temperature remains the same at -20C but many plates have been tested at -40 C on a per heat basis. S355NL - BEBON steelS355NL steel is used above all for manufacturing highly stressed welded structures in the construction of heavy machinery, bridges and steel structures.S355NL steel is available for application temperatures below -20 °C. There are many grades and the uses varied including civil and industrial engineering. High strength low alloys have replaced
Go here. Chemical composition % of steel S355NL (1.0546):EN 10025-3-2004. Nominal thickness =< 63 (mm) CEV max = 0.43. For long products the P and S content can be 0.005% higher. For railway application a maximum S content of 0.01% may be agreed at the time of enquiry and order. In sufficient other N-binding elements are present the minimum S355NL Steel Plates - Oakley SteelS355NL steel has a yield strength of 355 MPa at 16 mm at room temperature falling to 275 MPa at 250 mm. Its normalised. The S355NL plates are all from Dillinger so German steel and typically have EN10204 3.2 MTC . S355NL2 steel plate -- Shanghai Royal IndustryS355NL steel grade material No. Is 1.0490. EN 10025 S355NL2 steel have the good weldable and fine grain structural property. So, it can be used into the steel structural or welded vessel or pressure vessels. Standard :EN 10025-3. Dimension range :2-400mm * 1000-3800mm * 3000-18000mm. S355NL2 Low alloy high strength steel Mechanical Properties
S355NL Structural Steel Plates Specifications. Steel Standard:EN 10025-3. Thickness:6 mm to 200 mm. Width:from 2 metres wide to 3m. Length:Up to 12 metres. Third Party Inspection for S355NL:ABS, DNV, BV, GL, CCS, LR, RINA, KR, NK, CE, SGS, IKE, IEI or other quality department. Classification:Normalized rolled weldable fine grain structural steels. Structural Steel - S235, S275, S355 Chemical Composition May 11, 2012 · Plate 3:S275JR, sample 200x200x16mm thickness (specimen dimensions 10x10x55 mm), Charpy Test Impact (0 degrees Temp) Average result 187, Orientation Transverse. 0 0. Reply. Pallab Dutta says:November 19, 2019 at 3:00 AM I am stuck in a position where I need some help of expert like you. As per subjected standard table -1, nitrogen %, max 0 Structural Steel Plate and Strip to EN 10025The impact properties of quality JR products are verified only when specified at the time of order placement. Impact tests are performed on full size specimens (greater than or equal to 10mm) in the longitudinal direction. 2. Using test piece of width less than 10mm, the minimum values given in table 2 shall be reduced in
K2 indicates that the Impact Test was performed to 40 joules minimum at 20°C. G3 indicates delivery conditions are at the manufacturers discretion. The last letter, if applicable:H indicates Hollow Section. L indicates qualities with specified minimum values of impact energy at a temp. of 50°C.S355NL steel plate charpy impact test temperature - BBN Oct 15, 2020 · Steel strip is a branch of steel plate. Steel strip is a kind of narrow and long steel plate, also known as strip steel, S355NL steel plate produced by various steel rolling enterprises to meet the needs of different industrial departments and industrial production of various metal or mechanical products. The width of steel strip is within 1300mm, and the length is slightly different according to the